03-16-2019, 01:25 PM
(Modification du message : 03-16-2019, 01:41 PM par a supprimer merci.)
Oui, je suis bien d'accord avec cela.
Malheureusement, en demat, les choses ne s'arrêtent pas là !
Donc en tirer des conclusions générales qui consistent à dire que tous les lecteurs sont égaux n'est pas possible avec le simple test que tu as fait.
On est d'accord ?
Dans ton premier message, tu commences par "J'ai répondu que ça ne changerait rien au son.". Et bien non, ton test ne te permets pas d'en arriver à cette conclusion...
Voici ce que John Swenson expliquait en 2013 sur le sujet (ici: https://www.audioasylum.com/cgi/t.mpl?f=...o&m=125989). Depuis, il n'y a pas eu de progrès significatifs.
"I've been working on a new USB DAC design recently, so I have a setup that I'm continuously looking at with scopes and logic analyzers etc. In this situation the logic analyzer said everything was fine, the bits were perfect. A logic analyzer runs the analog voltage on the wire through a "threshold" to distinguish if it is high or low, what you see on the screen is just high or low, ie "bits". But when I looked with the scope which shows the actual voltage levels of the signal I saw some extra signal riding on top of the highs and lows of the "bits". This turned out to be noise on the ground plane caused by the processor that was generating the bits. (it was much worse than it should have been due to a poor board layout of the processor reference board) That noise was enough to cause significant change to the audio out even though the "bits" were correct.
One interesting aspect of this was that you could easily see changes in this ground plane noise depending on what the processor was doing. While this was a fairly gross example of the effect, it clealy shows that things going on in the processing and transmission of the bits can have an affect on the sound at the output, even though the correct bits get to the DAC chip.
Next you might ask "well isn't that a broken system, if it was "good" shouldn't it not be an issue?" Note that this was the official reference board for the processor made by the manufacturer, who should know how to make things that work well with their processor. This just goes to show that things that can cause audible differences in digital audio are frequently not part of "it works as a digital system", the board did what it was supposed to, it delivered the bits.
A better board design could have cut this ground noise down significantly, but it would still be there.
What we DAC designers have to do is figure out ways to design products that produce analog out that is immune to this sort of thing. Unfortunately this is extremely difficult to do. There are many people on this board that expect that this is easy to do, just put in the right 50cent part and presto the design is completely immune to everything. It doesn't work that way. High frequency ground noise is extremly pernicious stuff, it will find a way to get around just about any obsticle you throw in its path.
Different designers take different approaches to try and achieve this with varying degrees of success. The different approaches will usually be affective at decreasing susceptibility to different types of noise so one DAC model may not care about a certain aspect (say cable differences) while another may be pretty immune to cable aspects but be susceptible to timing variations in packets. This may be a part of why some people say they can hear certain aspects and others say they cannot.
These techniques for noise suppression are pretty esoteric knowledge, there really are only a few people that really understand all this, there are very few places in the real world were the combined knowlege to make this really work right are required, thus very few people have a good grasp on all of this. The result is that many actual designs on the market are fairly lacking in this department, or are only targeting one aspect of it.
This is slowly changing and companies are starting to get an inkling of what it takes to do well with this and are hiring people with some knowledge in this field, but there aren't nearly enough to go around, so it's going to be some time before all digital audio systems you can buy do a good job in this regard. "
Malheureusement, en demat, les choses ne s'arrêtent pas là !
Donc en tirer des conclusions générales qui consistent à dire que tous les lecteurs sont égaux n'est pas possible avec le simple test que tu as fait.
On est d'accord ?
Dans ton premier message, tu commences par "J'ai répondu que ça ne changerait rien au son.". Et bien non, ton test ne te permets pas d'en arriver à cette conclusion...
Voici ce que John Swenson expliquait en 2013 sur le sujet (ici: https://www.audioasylum.com/cgi/t.mpl?f=...o&m=125989). Depuis, il n'y a pas eu de progrès significatifs.
"I've been working on a new USB DAC design recently, so I have a setup that I'm continuously looking at with scopes and logic analyzers etc. In this situation the logic analyzer said everything was fine, the bits were perfect. A logic analyzer runs the analog voltage on the wire through a "threshold" to distinguish if it is high or low, what you see on the screen is just high or low, ie "bits". But when I looked with the scope which shows the actual voltage levels of the signal I saw some extra signal riding on top of the highs and lows of the "bits". This turned out to be noise on the ground plane caused by the processor that was generating the bits. (it was much worse than it should have been due to a poor board layout of the processor reference board) That noise was enough to cause significant change to the audio out even though the "bits" were correct.
One interesting aspect of this was that you could easily see changes in this ground plane noise depending on what the processor was doing. While this was a fairly gross example of the effect, it clealy shows that things going on in the processing and transmission of the bits can have an affect on the sound at the output, even though the correct bits get to the DAC chip.
Next you might ask "well isn't that a broken system, if it was "good" shouldn't it not be an issue?" Note that this was the official reference board for the processor made by the manufacturer, who should know how to make things that work well with their processor. This just goes to show that things that can cause audible differences in digital audio are frequently not part of "it works as a digital system", the board did what it was supposed to, it delivered the bits.
A better board design could have cut this ground noise down significantly, but it would still be there.
What we DAC designers have to do is figure out ways to design products that produce analog out that is immune to this sort of thing. Unfortunately this is extremely difficult to do. There are many people on this board that expect that this is easy to do, just put in the right 50cent part and presto the design is completely immune to everything. It doesn't work that way. High frequency ground noise is extremly pernicious stuff, it will find a way to get around just about any obsticle you throw in its path.
Different designers take different approaches to try and achieve this with varying degrees of success. The different approaches will usually be affective at decreasing susceptibility to different types of noise so one DAC model may not care about a certain aspect (say cable differences) while another may be pretty immune to cable aspects but be susceptible to timing variations in packets. This may be a part of why some people say they can hear certain aspects and others say they cannot.
These techniques for noise suppression are pretty esoteric knowledge, there really are only a few people that really understand all this, there are very few places in the real world were the combined knowlege to make this really work right are required, thus very few people have a good grasp on all of this. The result is that many actual designs on the market are fairly lacking in this department, or are only targeting one aspect of it.
This is slowly changing and companies are starting to get an inkling of what it takes to do well with this and are hiring people with some knowledge in this field, but there aren't nearly enough to go around, so it's going to be some time before all digital audio systems you can buy do a good job in this regard. "